View A6285EETTR-T_4201469.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

A6285 16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Features and Benefits
3.0 to 5.5 V logic supply range Schmitt trigger inputs for improved noise immunity Power-On Reset (POR) Up to 80 mA constant-current sinking outputs LED open circuit detection (LOD) Dot correction (DC) for adjusting LED light intensity on each channel with 7-bit resolution Low-power CMOS logic and latches High data input rate up to 30 MHz Active output pull-ups with enable/disable 20 ns typical staggering delay between outputs Internal UVLO and thermal shutdown (TSD) circuitry Fault output flags for an LED open circuit (LOD) or a thermal shutdown (TSD) condition
Description
The A6285 is designed for LED display applications. This BiCMOS device includes an On/Off shift register, a Dot Correction (DC) shift register, accompanying data latches, and 16 MOS constant-current sink drivers with active pull-ups that can be enabled or disabled as required by the application. The CMOS shift registers and latches allow direct interfacing with microprocessor-based systems. With a 3.3 or 5 V logic supply, typical serial data input rates can reach up to 30 MHz. The LED drive current level can be set by a single external resistor, selected by the application designer. A CMOS serial data output permits cascading of multiple devices in applications requiring additional drive lines. Individual LED light intensity can be adjusted to correct for light intensity variations by using the Dot Correction feature. Open LED connections can be detected, and then signaled back to the host microprocessor through the serial data output (SDO pin). The FAULT output flags an LED open circuit (LOD) condition or a thermal shutdown (TSD) condition. A staggering delay on the load outputs during ON/OFF transitions helps to reduce ground bounce.
Package: 32 Contact QFN (suffix ET)
5 mm x 5 mm 0.90 mm nominal overall height Continued on the next page... Not to scale
Typical Application
VDD VLED VLED 10 F PE OUT0 OUT15
100 K SDI FAULT Controller CLK LE MODE OE SDI FAULT CLK LE MODE OE
SDO VDD
A6285
100 nF
REXT SDO
6285-DS
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Description (continued) The device is available in a 32-lead QFN (package ET), with an exposed thermal pad. It is lead (Pb) free with 100% matte tin leadframe plating.
Applications include the following: Display backlighting Monocolor, multicolor, or full-color LED display Monocolor, multicolor, LED Signboard Multicolor LED lighting
Selection Guide
Part Number A6285EET-T A6285EETTR-T Package 5x5 mm QFN, 32 pin, exposed thermal pad 5x5 mm QFN, 32 pin, exposed thermal pad Packing (estimated) 73 pieces per tube 1500 pieces per 7-in reel 7000 pieces per 13-in. reel
Absolute Maximum Ratings
Characteristic Supply Voltage* OUTx Current (any single output) Input Voltage Range* LED Load Supply Range* ESD Rating Operating Temperature Range (E) Junction Temperature Storage Temperature Range *With respect to ground (GND, PGND). TA TJ(max) Tstg Symbol VDD IO VI VLED HBM (JEDEC JESD22-A114, Human Body Model) CDM (JEDEC JESD22-C101, Charged Device Model) VOE, VLE, VCLK, VSDI, VMODE Notes Min. -0.3 - -0.3 -0.3 - - -40 - -55 Max. 5.5 90 VDD + 0.3 13.2 1.5 1.0 85 150 150 Unit V mA V V kV kV C C C
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
2
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Functional Block Diagram
0 1 Status Info: LOD 0 15
VDD 1
15
TSD
FAULT
MODE
1 MODE 0
LOD
LE
CLK SDI
MODE 0
UVLO POR
VDD
1 0 MODE
ON/OFF Shift Register 0 15 0
DC Shift Register 111
1 0 MODE
SDO
LE
1 0 MODE
TSD
ON/OFF Register 0
DC Register 0 6
ON/OFF Register 1
DC Register 7 13
ON/OFF Register 15
DC Register 105 111
OE
UVLO
PAD
LOD 0
7-Bit DC
LOD 1
7-Bit DC
LOD 15
7-Bit DC
REXT GND
Io Regulator
PE
OUT0
OUT1
OUT15 VLED
(Note: Resistor values are equivalent resistance and not tested.)
VDD CLK, SDI, LE, MODE, O E 500
Inputs and Outputs Equivalent Circuits
Active Pull-up Cell
(1 of 16 Outputs)
PE 5 mA
VDD
VLED
10
SDO
ON OUTx
10
FAULT
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
3
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Pin-out Diagram
25 FAULT 24 SDO 23 PE 22 OUT15 PAD 21 OUT14 20 PGND 19 OUT13 18 OUT12 17 OUT11 OUT5 9 PGND 10 OUT6 11 OUT7 12 OUT8 13 OUT9 14 PGND 15 OUT10 16 26 MODE 27 REXT 29 GND 28 VDD 32 CLK SDI 1 NC 2 OUT0 3 OUT1 4 PGND 5 OUT2 6 OUT3 7 OUT4 8 30 OE 31 LE
Terminal List Table
Name O E GND PE REXT MODE NC OUT0 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 OUT9 OUT10 OUT11 OUT12 OUT13 OUT14 OUT15 PGND CLK SDI SDO VDD FAULT LE PAD Number 30 29 23 27 26 2 3 4 6 7 8 9 11 12 13 14 16 17 18 19 21 22 5, 10, 15, 20 32 1 24 28 25 31 -
Description Output Enable input. Active low. When O = High, all OUTx outputs are forced OFF. When O = Low, E E ON/OFF of OUTx outputs are controlled by input data. Logic supply ground. Active Pull-up Enable. When connected to LED Load Supply (VLED) = enabled, when connected to PGND = disabled. Reference current input/output terminal. Logic input, Mode select. When MODE = Low, then SDI, SDO, CLK, LE are connected to ON/OFF control logic. When MODE = High, SDI, SDO, CLK, LE are connected to dot-correction logic. No connection. Not internally connected.
Constant current outputs.
Power ground. Data shift clock input. Note that the internal connections are switched by input at MODE pin. At CLK, the shift-registers selected by MODE shift the data. Serial Data In. Data input of serial data interface. Serial Data Out. Data output of serial data interface. Logic Supply. Error output. FAULT is open drain terminal. FAULT goes low when LOD or TSD detected. Latch Enable input. Note that the internal connections are switched by input at the MODE pin. At LE, the latches selected by MODE get new data. Exposed pad for enhanced thermal dissipation; not connected internally, connect to power ground plane.
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
4
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Operating Characteristics
ELECTRICAL CHARACTERISTICS at TA1 = 25C, VDD = 3.0 to 5.5 V, unless otherwise noted
Characteristic Logic Supply Voltage Range LED Load Supply Output Voltage Undervoltage Lockout Output Current Symbol Test Conditions VDD Operating VLED Operating VDD 0 5.0 V VDD(UV) VDD 5 0.0 V VDS = 1 V, REXT = 600 IO VDS = 1 V, REXT = 1.2 k 1 V = VDS(x), REXT = 600 ; All outputs on Err 1 V = VDS(x), REXT = 1.2 k; All outputs on VDS(X) = 1 to 3 V, REXT = 600 ; IOreg All outputs on VOH = 12 V IDSS VIH VIL VIhys All digital inputs II All digital inputs IOL = 1 mA VOL VOH IOH = -1 mA REXT = 9.6 k, VOE = 5 V IDD(OFF) REXT = 1.2 k, VOE = 5 V All outputs on, REXT = 1.2 k, VO = 1 V, data transfer 30 MHz IDD(ON) All outputs on, REXT = 600 , VO = 1 V, data transfer 30 MHz VOUT(0) IOUT = 5 mA; faults asserted IOUT(1) VOUT = 5.5 V, open drain; faults negated IOUT(0) VLED = 1 V, all outputs off TJTSD Temperature increasing TJTSDhys VLOD VEXT REXT = 600 Min. 3.0 - 2.5 2.3 70 35 - - - - 0.8xVDD GND 250 -1 - VDD - 0.5 - - - - - - - - - - 1.21 Typ.2 5.0 - 2.7 2.5 80 40 +1.0 +1.0 - - - - - - - - - - - 26 - - 2.8 165 15 0.30 1.25 Max. 5.5 12.0 2.9 2.7 90 45 +4.0 +4.0 +6.0 0.5 VDD 0.2xVDD 900 1 0.5 - 6 17 25 35 0.4 1 - - - 0.40 1.31 Unit V V V V mA mA % % % A V V mV A V V mA mA mA mA V A mA C C V V
Output to Output Matching Error4
Load Regulation Output Leakage Current Logic Input Voltage Logic Input Voltage Hysteresis Logic Input Current SDO Voltage
Supply Current3
FAULT Output Active Pull-up Thermal Shutdown Temperature Thermal Shutdown Hysteresis Open LED Detection Threshold Reference Voltage at REXT
1Tested 2Typical
at 25C. Specifications are assured by design and characterization over the operating temperature range of -40C to 85C. data are for initial design estimations only, and assume optimum manufacturing and application conditions. Performance may vary for individual units, within the specified maximum and minimum limits. 3Recommended operating range: V = 1.0 to 3.0 V. O 4Err = (I (min or max) - I (av)) / I (av). O O O
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
5
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
SWITCHING CHARACTERISTICS at TA1 = 25C, VDD = VIH = 3.0 to 5.5 V, VDS = 1 V, VIL = 0 V, REXT = 1.2 k, IO = 40 mA,
VL = 3 V, RL = 51 , CL = 15 pF (see table 9)
Characteristic Clock Frequency Clock Pulse Duration Clock Frequency (cascaded) LE Pulse Duration Symbol fCLK twh0/twl0 fCLKC twh1 tsu0 Setup Time tsu1 tsu2 tsu3 th0 Hold Time th1 th2 th3 tr0 Rise Time tr1 tf0 Fall Time tf1 tpd0 tpd1 Propagation Delay Time tpd2 tpd3 tpd4 tpd5 LOD Sample and Read Time Output Delay Time
1Tested 2Typical
Test Conditions CLK CLK = High/Low CLK LE = High SDI to CLK CLK to LE MODE to CLK MODE to LE CLK to SDI LE to CLK CLK to MODE LE to MODE SDO, 10/90% points (see figure 1) OUTx, VDD = 5 V, DC = 127, 10/90% points (see figure 2) SDO, 10/90% points (see figure 1) OUTx, VDD = 5 V, DC = 127, 10/90% points (see figure 2) CLK to SDO (see figure 1) MODE to SDO (see figure 1) O to OUT0 (see figure 2) E LE to OUT0 (see figure 2) OUTx to FAULT (see figures 2 and 3) LE to IOUT (DC) (see figure 2) LE1 to LE2 OUTx to OUT(x+1) (see figure 2)
Min. - 16 - 20 10 10 10 10 10 10 10 10 - - - - - - - - - - 1660 10
Typ.2 - - - - - - - - - - - - - 10 - 10 - - - - - - - 20
Max. 30 - 25 - - - - - - - - - 16 30 16 30 30 30 60 60 1000 200 - 40
Unit MHz ns MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
tLOD td
at 25C. Specifications are assured by design and characterization over the operating temperature range of -40C to 85C. data are for initial design estimations only, and assume optimum manufacturing and application conditions. Performance may vary for individual units, within the specified maximum and minimum limits d maximum and minimum limits.
Parameter Measurement Information
A6285 SDO OUTx 15 pF 15 pF FAULT A6285 51 A6285 1.2 k
Figure 1. Test circuit for tr0, tf0, td0, and td1
Figure 2. Test circuit for tr1, tf1, tpd2, tpd3, tpd5, and tpd6
Figure 3. Test circuit for tpd4
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
6
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Operating Characteristics
9090 VDS = 1 V DC= 127 8080 7070
OLC (mA) IIO (mA)
100
REXT = 600
10
REXT = 800
6060 5050 REXT = 1.2 k 4040 3030 REXT = 2.4 k 2020 1010
REXT (k)
1 0.1 0 10 20 30 40 50 60 70 80
IO(max) (mA)
Figure 4. Value of external reference resistor, REXT, versus channel Constant Output Current
00 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 VO V (V) (V)
O
Figure 5. Output Voltage versus Output Current at various levels of REXT
Thermal Characteristics
Characteristic Symbol Test Conditions1 PD Package Power Dissipation Continuous, TA = 25C Package Thermal Resistance RJA 4-layer PCB based on JEDEC standard 1Additional thermal information available on Allegro website. 2Actual performance significantly affected by application.
5.0
Value2 3.9 32
Units W C/W
ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS
4.0
3.0
Pa
ck
ag e
ET ,R
JA
=
32
2.0
C
/W
1.0
0
25
50 75 100 125 AMBIENT TEMPERATURE IN C
150
Figure 6. Power Dissipation versus temperature
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
7
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Functional Description
Setting Maximum Channel Current The maximum output current per channel is set by a single external resistor, REXT, which is placed between the REXT pin and PGND. The voltage on REXT, VEXT , is set by an internal band gap. The maximum channel current is equivalent to the current flowing through REXT multiplied by 38.4. The maximum channel output current can be calculated as: register. The timing sequence is shown in figure 9. All Channel Output Enable-Disable All OUTx channels of the A6285 can switched off using the O pin. When OE is E set high, all OUTx outputs are disabled, regardless of the on/off status of any OUTx. When O is set to low, the on/off status of E each OUTx is determined by the state of the latches in the On/Off register. O can be PWMed to control the average current, which E controls the LED brightness of all outputs, in addition to the DC function. Individual Channel Output Enable-Disable Each OUTx channel can be switched on or off independently. Each of the channels can be programmed with a 1-bit word. On/off data is entered for all channels at the same time. The complete on/off data format consists of sixteen 1-bit words, which form a 16-bit wide serial data packet. The data for each channel is sent in a continuous sequence, and all data is clocked in with the MSB first, as shown in figure 8. To input data into the On/Off register, LE must be set low, and MODE must be set low. LE allows on/off data to enter the input shift register, and MODE sets the input shift register to 16-bit width. After all serial data is clocked in, a rising edge on the LE terminal latches the data into the On/Off register and moves the LOD data at the Open Circuit Detector into the input shift register. The timing sequence is shown in figure 9.
IO(max) =
where: VEXT is 1.25 V typical, and
VEXT x 38.4 , REXT
(1)
REXT is the value of the user-selected external resistor, which should not be less than 600 , corresponding to 80 mA. Figure 4 shows the maximum per channel constant output current, IO(max), of OUT0 to OUT15, versus REXT ,, the value of the resistor between REXT terminal and ground. Dot Correction The A6285 can independently fine-adjust the current of each output channel, a feature referred to as dot correction. This feature is used to compensate for the brightness deviations of the LEDs connected to the output channels, OUT0 through OUT15. Each of the 16 channels can be programmed with a 7-bit word. The channel output can be adjusted in 128 steps from 0% to 100% of the maximum programmable per channel output current, IO(max). Equation 2 determines the output current for each OUTx:
LSB
MSB
0
DC 0.0
I (max) x DCx , IOx = O (2) 127 where DCx is the programmed dot-correction value (0, 1, ...127)
for each output channel. Dot correction data is entered for all channels at the same time. The complete dot correction data format consists of sixteen 7-bit words, which form a 112-bit (16 x 7) wide serial data packet. The data for each channel is sent in a continuous sequence, and all data is clocked in with the MSB first, as shown in figure 7. To input data into the Dot Correction register, LE should be set low, and MODE must be set high. MODE sets the input shift register to 112-bit width. After all serial data is clocked in, a rising edge on the LE terminal latches the data into the Dot Correction
...
DCOUT0
6
DC 0.6
7
DC 1.0
...
104 DC 14.6
105 DC 15.0
...
DCOUT15
111 DC 15.6
DCOUT2 through DCOUT14
Figure 7. Dot Correction (DC) data format
LSB
MSB
0
On/Off
1
On/Off
...
14
On/Off
15
On/Off
OUT0
OUT1 through OUT14
OUT15
Figure 8. Individual output on-off data format
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
8
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Delay Between Outputs The A6285 has graduated delay
circuits between outputs. The fixed delay time is 20 ns (typical). OUT0 has no delay, OUT1 has a 20 ns delay, OUT2 has a 40 ns delay, and so forth. This delay prevents large in-rush currents that create ground bounce, which reduces power supply bypass capacitor requirements when the outputs turn on. The delays work during switch on and switch off of each output channel.
required to input data into the device. The rising edge of a CLK signal shifts the data from SDI pin to the input shift register. After all data is clocked in, a rising edge of LE latches the serial data to the On/Off register. All data is clocked in with the MSB first, while LE is set low. Multiple A6285 devices can be cascaded by connecting the SDOpin of one device with the SDI pin of the following device. The SDO pin can also be connected to the microcontroller or microprocessor in order to transmit LOD information from the A6285.
Serial Interface Data Transfer Rate The A6285
includes a flexible serial data interface, which can be connected to a microcontroller or a digital signal processor. Only 3 pins are
Figure 9. Output on-off and Dot Correction timing
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
9
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
up to VDD with a single pull-up resistor, as shown in figure 10. This reduces the number of signals needed to report faults. To determine whether the fault is a TSD or an LOD, LOD can be masked by setting O = high. However, it cannot be determined E if both a TSD and an LOD condition are present. The FAULT Truth Table is shown on page 11. Active Pull-up Enable, PE The A6285 provides active pull-ups on each output determined by the PE pin. When the LED supply, VLED , is tied to the PE pin, the active pull-ups are enabled. When the PE pin is tied to ground, the active pull-ups are disabled. The Active Pull-up Enable is also current-limited to 2.8 mA typical, preventing possible damage to the device in the event of a short-to-ground. This feature can eliminate ghosting in multiplexing applications. Undervoltage Lockout (UVLO) and Power-On Reset (POR) The A6285 includes an internal undervoltage lockout circuit that disables the outputs in the event that the logic supply voltage drops below a minimum acceptable level. This feature prevents the display of erroneous information, a function necessary for some critical applications. A Power-On Reset (POR) is performed upon recovery of the logic supply voltage after a UVLO event and at power-up. During POR, all internal shift registers and latches are set to 0. Thermal Shutdown Protection and Fault Flag (TSD) The A6285 provides thermal protection when the device is overheated, typically a result of excessive power being dissipated in the outputs. If the junction temperature exceeds the threshold
V LED V LED
Figure 10 shows an example application with n cascaded A6285 devices connected to a controller. The maximum number of cascaded devices depends on the application system and the data transfer rate. The minimum data input transfer rate is calculated as follows:
fCLK = 112 x fUPDATE x n ,
where:
(3)
fCLK is the minimum data input frequency for CLK and SDI, fUPDATE is the update rate of the entire cascaded system, and n is the number of cascaded A6285 devices. Operating Modes The A6285 has two operating modes, determined by the MODE signal: * On-Off mode (MODE = low) * Dot Correction mode (MODE = high) Fault Output, FAULT The open-drain output FAULT is used to report both of the fault flags, LOD and TSD. During normal operating conditions, the internal transistor connected to the FAULT pin is turned off. The voltage on FAULT is pulled up to VDD through a external pull-up resistor. If an LOD or TSD condition is detected, the internal transistor is turned on, and FAULT is pulled to PGND. Because FAULT is an open-drain output, multiple ICs can be ORed together and pulledVDD V LED V LED
100 k PE SDI FAULT CLK LE Controller MODE OE SDI FAULT CLK LE MODE OE
...
OUT0 OUT15 SDO VDD
100 nF
...
PE SDI FAULT CLK LE MODE REXT OE A6285 REXT
100 nF
OUT0
OUT15 SDO VDD
A6285
SDO
IC 1 5
IC n
Figure 10. Schematic of cascaded A6285 devices
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
10
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
the input shift register every time On/Off data is moved into the On/Off Register, although in reality, the previous LOD status is being moved into the input shift register. If an LOD condition was previously detected, a 1 for each open LED will be moved from the Open Circuit Detector into the input shift register, where it can be read on the SDO pin. 4. The existing LOD condition is sampled within 2 s of the outputs turning on and the resulting status data waits at the Open Circuit Detector until moved into the input shift register on the rising edge of the next LE pulse. 5. The cycle is repeated when new On/Off data is clocked into the input shift register. As new data is being clocked in, LOD status data is being clocked out of the SDO pin, where it can be read by a microprocessor. Note: It is not necessary to load new On/Off data in order to view the LOD status waiting at the Open Circuit Detector. A second LE pulse will put the LOD data into the input shift register. However, LOD data that is presently in the input shift register will be moved into the On/Off Register, generating a "blank" display. Such a blank display may be undesirable; therefore, a second LE pulse should not be applied without first clocking in useful On/Off data for updating the display. The update interval between LE pulses ( LE1 to LE2 ), referred to as the LOD Sample and Read Time, tLOD , must be at least 1660 ns to allow for settling and staggered delays. Figure 11 shows the LOD serial data format. The FAULT truth table is shown below.
LSB MSB
temperature, TTSDF , of 165C (typical), all driver outputs will be turned off and a TSD fault will be flagged. The TSD flag will pull the FAULT output pin to PGND (low). After a 15C (typical) drop in junction temperature, the outputs will turn back on and the FAULT pin will be pulled back to VDD (high). The input shift register and the latch register will remain active during a TSD event. Therefore, there is no need to reset the data in the output latches. However, the TSD cycle will continue until the thermal problem is corrected. LED Open Detection (LOD) The A6285 provides LED open circuit detection. This circuit flags a fault and pulls the FAULT pin to PGND (low) if any of the 16 OUTx LEDs are open or disconnected from the circuit. The LOD circuit flags a fault when all of the following conditions are met: * O is set low E * The voltage at each OUTx pin is sampled after being turned on * VOUTx < VLOD (0.3 V typical) MODE may be set either high or low. However, to perform a complete LOD cycle, which includes reading the LOD status of each OUTx, MODE must be set low. A complete LOD cycle is described as follows: 1. On/Off data is clocked into the input shift register. 2. LE is pulsed to move the On/Off data into the On/Off Register. The data is moved on the rising edge of LE. If an LOD condition is present, the FAULT output is immediately pulled to PGND (low). 3. Data present at the Open Circuit Detector (sampled when data was moved into the On/Off Register on the previous transition of LE) is immediately moved into the input shift register on the same rising edge of LE. If no LOD condition was previously detected, all 0s are present at the Open Circuit Detector. Thus, all 0s are moved into the input shift register. This gives the appearance of "clearing"
FAULT Truth Table
0
LOD
1
LOD
...
14
LOD
15
LOD SDO
OUT0
OUT1 through OUT14
OUT15
Figure 11. Individual output LOD data format
Junction Temperature TJ < TTSD TJ < TTSD TJ < TTSD TJ < TTSD TJ > TTSD TJ > TTSD TJ > TTSD TJ > TTSD
Conditions Outx Voltage Outx > VLOD Outx < VLOD Outx > VLOD Outx < VLOD Outx > VLOD Outx < VLOD Outx > VLOD Outx < VLOD
Output Enable, O E H H L L H H L L
Fault Output H H H L L L L L
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
11
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Application Information
Load Supply Voltage (VLED) These devices are designed to operate with driver voltage drops (VDS) of 1.0 to 3.0V, with one or more LED forward voltages, VF , of 1.2 to 4.0 V. If higher voltages are dropped across the driver, package power dissipation will increase significantly. To minimize package power dissipation, it is recommended to use the lowest possible load supply voltage, VLED, or to set any series voltage dropping, VDROP , according to the following formula: VDROP = VLED - VF - VDS , with VDROP = IOx RDROP for a single driver or for a Zener diode (VZ), or for a series string of silicon diodes (approximately 0.7 V per diode) for a group of drivers (see figure 3). If the available voltage source will cause unacceptable power dissipation and series resistors or diodes are undesirable, a voltage regulator can be used to provide VLED. For reference, typical LED forward voltages are:
LED Type White Blue Green Yellow Amber Red Infrared VF (V) 3.5 to 4.0 3.0 to 4.0 1.8 to 2.2 2.0 to 2.1 1.9 to 2.65 1.6 to 2.25 1.2 to 1.5
Pattern Layout The logic and power grounds should be kept separate, terminated at one location. The exposed metal pad must be connected to a large power ground plane, allowing the copper to dissipate heat. Where multiple devices are cascaded, multilayer boards are recommended. REXT should be placed as close as possible to the device, keeping a short distance between the REXT pin and ground. Decoupling capacitors should be used liberally. 0.1 F should be placed on the logic supply pin, and 10 F placed between the common VLED line and the device ground at least at every second device. Package Power Dissipation (PD) The maximum allowable package power dissipation based on package type is determined by: PD(max) = (150 - TA) / RJA , where RJA is the thermal resistance of the package mounted on the circuit board, determined experimentally. Power dissipation levels based on the package are shown in the Package Thermal Characteristics section (see page 7). The actual package power dissipation is determined by: PD(act) = DC x (VDS x IOx 16) + (VDDx IDD) , where DC is the duty cycle. The value 16 represents the maximum number of available device outputs. When the load supply voltage, VLED, is greater than 3 to 5 V, and PD(act) > PD(max), an external voltage reducer (VDROP) must be used (see figure 12). Reducing the percent duty cycle, DC, will also reduce power dissipation.
Figure 12. Typical application voltage drops
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
12
A6285
16-Channel Constant-Current Latched LED Driver with Open LED Detection and Dot Correction
Package ET, 5 mm x 5 mm, 32-pin QFN with Exposed Thermal Pad
5.00 0.15 32 1 2 A 5.00 0.15 1.00 1 2
0.30 32
0.50
3.40
5.00
1 33X D 0.08 C +0.05 0.25 -0.07 SEATING PLANE 0.90 0.10 0.50 C 3.40 5.00
C
PCB Layout Reference View
+0.15 0.40 -0.10 3.40 2 1 32 3.40 B
All dimensions nominal, not for tooling use (reference JEDEC MO-220VHHD-6) Dimensions in millimeters Exact case and lead configuration at supplier discretion within limits shown A Terminal #1 mark area B Exposed thermal pad (reference only, terminal #1 identifier appearance at supplier discretion) C Reference land pattern layout (reference IPC7351 QFN50P500X500X100-33V6M); All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances; when mounting on a multilayer PCB, thermal vias at the exposed thermal pad land can improve thermal dissipation (reference EIA/JEDEC Standard JESD51-5) D Coplanarity includes exposed thermal pad and terminals
Copyright (c)2007-2008, Allegro MicroSystems, Inc. The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro's products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the failure of that life support device or system, or to affect the safety or effectiveness of that device or system. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. For the latest version of this document, visit our website: www.allegromicro.com
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
13

▲Up To Search▲

Price & Availability of A6285EETTR-T

	To Download A6285EETTR-T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .